ASTM D1194 PDF

ASTM D, Bearing Capacity of Soils for Static Load & Spread Footings – Download as PDF File .pdf), Text File .txt) or read online. Find the most up-to-date version of ASTM D at Engineering In each increment; the load stays static for 15 minutes according to ASTM D 94 specification. The results showed that the plate settlements of the soil under.

Author: Bar Kale
Country: Benin
Language: English (Spanish)
Genre: Spiritual
Published (Last): 17 October 2004
Pages: 87
PDF File Size: 2.67 Mb
ePub File Size: 10.4 Mb
ISBN: 723-3-31331-440-2
Downloads: 16340
Price: Free* [*Free Regsitration Required]
Uploader: Baktilar

Precise leveling optical survey to accuracy of 0. The applied load shall be measured using calibrated electronic load cell.

ASTM makes withdrawn standards available for informational purposes.

Are you an Engineering professional? Promoting, selling, recruiting, coursework and thesis posting is forbidden. For bearing asm, three circular steel bearing plates, not less than 25mm in xstm and varying in diameter from mm to mm including the minimum and maximum diameter specified or square steel bearing plates of equivalent area. Red Flag This Post Please let us know here why this post is inappropriate. A standard may be withdrawn with or without replacement. The load test consists in transmitting to the soil to be tested and the subsequent increasing load increments, detecting simultaneously the sagging and therefore allows to directly determine a form of deformation or compressibility of the soil.

Satm plate bearing load test shall be discontinued if any of the following d11194 The subsidence induced by the ground plate are simultaneously detected by centesimal or digital data acquisition systems, integral with a frame of reference outside the area of influence of the applied load.

Download Now White Paper: Plate Load testing is usually used for the verification of the bearing capacity of the land of the substrate, of the foundation layer and the base layer of the flooring, although it is not uncommon to its use to investigate the bearing capacity of the soil surface or to the state compaction of granular materials and road surfaces.

  JULIA URQUIDI LO QUE VARGUITAS NO DIJO PDF

In addition to the continuous listing awtm all time, load, and settlement data for each test, the report shall include at least the followings:. Download Now Defense manufacturing is all about project manufacturing and project accounting. As an alternative, three small concrete footings of the size mentioned or larger can be cast in-situ.

Register now while it’s still free! Defense manufacturing is astj about project manufacturing and project accounting. By joining you are opting in to receive e-mail.

Plate Load Testing

Reasons such as off-topic, duplicates, flames, illegal, vulgar, or students posting their homework. Posting Guidelines Promoting, selling, recruiting, coursework and thesis posting is forbidden.

Join your peers on the Internet’s largest technical engineering professional community. Resources Digital Transformation may be defined in a number of different ways by analysts or enterprise software vendors. Such d1914 must have a depth of not less than two thirds of their width.

The details of equipment including the certificates of instrument and copies of calibration charts from approved agency and setup for conducting the plate load test shall be submitted for the approval by the Engineer before commencement of the test. The reference beam and measuring devices should be protected from the direct rays of the sun and from wind by means of tarpaulins or other forms of shelter, to minimize errors of measurement which can easily arise from these causes.

Proctor penetrometer | Matest

Close this window and log in. The load transmission takes place via the application of a force by means of a hydraulic system of thrust, of a circular plate. Students Click Here Join Us!

  COMAC CS 140 PDF

Digital Transformation may be defined in a number of different ways by analysts or enterprise software vendors. It’s easy to join and it’s free.

Subcommittees responsible for standards develop can withdraw a standard if they consider that it has limited continued use value. In rock, plates larger than mm diameter may be used, depending on the jointing frequency.

The two active ones are for pavement design, but you can gain the same type of info. Thank you for helping keep Eng-Tips Forums free from asstm posts. The Hydraulic or V1194 Jack Assembly should have sufficient capacity to provide and maintain the maximum estimated load but not less than 50 tons in any case. The plate load test shall be carried out at locations as shown in the drawings or as directed by the Engineer using approved equipment. Click Here to join Eng-Tips and talk with other members!

Miscellaneous Apparatus required, including loading columns, steel shims, and other construction tools and equipment required for preparation of the test pits and loading apparatus.

Of fundamental importance, in any case, is the use of the proper contrast medium whose mass is a function of the expected load. This test was rarely done for d114 purpose anymore. The Settlement-Recording Devices, such as dial gauges should be able to measure to an accuracy of at least 0. There are two active plate load tests that can be used The Eng-Tips staff will check this out and take appropriate action.

Author: admin