HUAWEI CDMA BTS 3606 PDF

Default Re: Huawei CDMA E BTS Max Power??? HI I think it can be more than 20W because the RF board support MAX 60W. The 3rd Global CDMA Operation and Development Forum, themed. To illustrate this further, we can note that Huawei BTSCE power With Huawei latest CDMA BTS products, based upon the physical network. indoor type) and BTSAC (for outdoor type) are The complete series of CDMA BTSs, and relevant Thus, for the same traffic in a sector, a Huawei BTS.

Author: Vit Grorn
Country: Timor Leste
Language: English (Spanish)
Genre: Business
Published (Last): 25 December 2007
Pages: 287
PDF File Size: 16.80 Mb
ePub File Size: 19.66 Mb
ISBN: 469-6-71160-902-5
Downloads: 92714
Price: Free* [*Free Regsitration Required]
Uploader: Kajirisar

Lead the bolts through the lower support.

Huawei BTS Baseband Subsystem

Figure shows RF cable connections, indicated by blue lines. Procedure To prepare power cables, proceed as follows Outline Figure shows the outline of the lower support. buawei

This chapter describes how to install and use these two types of DDF. Tools The following tools are required: Figure Installing a cabinet on the floor without sufficient bearing capacity Paint the whole support with rustproof coat and top-coat. For the 24 V power input, the voltage drop of the cable from the 24 V power supply system to the power input port of the BTS must be less than or equal to 0.

Connect the two probes to the paint-free place of the base and the expansion bolt.

Huawei CDMA E BTS Max Power ???

No field installation of the fan box is required. The cabinet is placed upside down. Note, Comment, Tip, Knowhow, Thought: Fix them onto the units. Got it, continue to print. The depth of the hole must range from 52 mm 2 in. If the outer package is damaged or soaked; or the equipment is soaked and becomes rusty, stop unpacking and find the cause.

  LO BUENO DE VERDAD VIRGINIE DESPENTES PDF

Bst the installation location for the DDF according to the engineering design for the equipment room. For the proper storage, use and disposal of this product, national laws and regulations huaei be observed.

Otherwise, the equipment will suffer severe damages.

Thus, you do not need to install these cables on site. Tighten the bolts on the cover.

Huawei BTS3606 Installation Manual

Feed back the situation to the local Huawei Representative Office. Please feel free to contact our local office or company headquarters. Page 14 – Power Supply Conditions of the Equipment Table of Contents Add to my manuals Add.

By pressing ‘print’ button you will print only current page.

CDMA grows greener

Don’t show me this message again. Determine the length of the grounding cables according bys their actual cabling path, that is, the route from the binding post of BTS cabinet to the wiring holes of the grounding protection bar of the cabinet. O 2 Configuration The O 2 refers to an omni cell with two carriers. Align the holes on the antistatic floor with the connecting holes of the support.

  HIPPOLYTUS REFUTATION OF ALL HERESIES PDF

The BTS in the multi-channel mode does not support the power synthesis function. The sectional area is 35 cables BtzL: Installing the Lower Support To install the lower support, proceed as follows: Diagonally fasten them to a 45 N-m in-lbas shown in Figure Installation Method You need to prepare the U-bar support on the site. Anchor bolt for the floor d expansion bolt d height-lock bolt first in the middle, then on both sides To fix the support, proceed as follows: Insert the boards according to the names on the relevant nameplates to huaqei any mistake.

Page 70 – Distributing Protection Grounding Cables Tighten the bolts at the front face of the huxwei. Normally, the fan box is installed upon delivery. Figure shows how to install a BTS cabinet on the cement floor. The letters A, B, C as shown in Figure are not cable labels. Figure illustrates the positions of installation holes for U-bar supports. To locate the support at the side of antistatic floor, proceed as follows: Make sure that all the power modules are well connected with the backplanes, and that other boards and modules such as the CTRM and CHPA are not inserted in the slots of the backplanes.

The sectional area is

Author: admin